Choose by task.
Fit by specification.
Diamond cutting, grinding and finishing references, with the original size and grit distinctions retained.
Thin diamond cutting disc · 125 mm
| Material | Diamond abrasive (catalog material) |
|---|---|
| Specification | 125 mm · 1.1mm · bore 22.23mm |
| Use | Tile and ceramic cutting; select the disc-rated workpiece and operating method. |
| Range-building advantage | A clearly specified diameter, bore and section lets buyers select by fit rather than appearance. |
Thin diamond cutting disc · 115 mm
| Material | Diamond abrasive (catalog material) |
|---|---|
| Specification | 115 mm · 1.1mm · bore 22.23mm |
| Use | Tile and ceramic cutting; select the disc-rated workpiece and operating method. |
| Range-building advantage | A clearly specified diameter, bore and section lets buyers select by fit rather than appearance. |
Thin diamond cutting disc · 110 mm · 03
| Material | Diamond abrasive (catalog material) |
|---|---|
| Specification | 110 mm · 1.1mm · bore 20mm |
| Use | Tile and ceramic cutting; select the disc-rated workpiece and operating method. |
| Range-building advantage | A clearly specified diameter, bore and section lets buyers select by fit rather than appearance. |
Thin diamond cutting disc · 105 mm · 04
| Material | Diamond abrasive (catalog material) |
|---|---|
| Specification | 105 mm · 1.1mm · bore 20mm |
| Use | Tile and ceramic cutting; select the disc-rated workpiece and operating method. |
| Range-building advantage | A clearly specified diameter, bore and section lets buyers select by fit rather than appearance. |
Diamond cutting / grinding disc · 105 mm
| Material | Diamond abrasive (catalog material) |
|---|---|
| Specification | 105 mm · 1.3mm · bore 20mm |
| Use | Cutting and edge grinding where the disc marking permits both operations. |
| Range-building advantage | A clearly specified diameter, bore and section lets buyers select by fit rather than appearance. |
Diamond cutting disc · 106 mm
| Material | Diamond abrasive (catalog material) |
|---|---|
| Specification | 106 mm · 1.1mm · bore 20mm |
| Use | Cutting selection for the specified workpiece and disc-rated operation. |
| Range-building advantage | A clearly specified diameter, bore and section lets buyers select by fit rather than appearance. |
Concrete-removal grinding wheel · 110mm
| Material | Diamond abrasive (catalog material) |
|---|---|
| Specification | 110mm · 5mm · bore 20mm |
| Use | Removing concrete surface material with a matching grinding setup. |
| Range-building advantage | A clearly specified diameter, bore and section lets buyers select by fit rather than appearance. |
Stone grinding wheel · 110mm
| Material | Diamond abrasive (catalog material) |
|---|---|
| Specification | 110mm · 5mm · bore 20mm |
| Use | Grinding stone surfaces with a matching grinding setup. |
| Range-building advantage | A clearly specified diameter, bore and section lets buyers select by fit rather than appearance. |
Compact diamond grinding wheel · 55mm
| Material | Diamond abrasive (catalog material) |
|---|---|
| Specification | 55mm · 5mm · bore 20mm |
| Use | Surface preparation / finishing selection; match profile, grit and backing to the workpiece. |
| Range-building advantage | A clearly specified diameter, bore and section lets buyers select by fit rather than appearance. |
Diamond grinding cup · 65mm
| Material | Diamond abrasive (catalog material) |
|---|---|
| Specification | 65mm · 5mm · bore 20mm |
| Use | Surface preparation / finishing selection; match profile, grit and backing to the workpiece. |
| Range-building advantage | A clearly specified diameter, bore and section lets buyers select by fit rather than appearance. |
Diamond grinding cup · 80mm
| Material | Diamond abrasive (catalog material) |
|---|---|
| Specification | 80mm · 5mm · bore 20mm |
| Use | Surface preparation / finishing selection; match profile, grit and backing to the workpiece. |
| Range-building advantage | A clearly specified diameter, bore and section lets buyers select by fit rather than appearance. |
Diamond grinding cup · 100mm
| Material | Diamond abrasive (catalog material) |
|---|---|
| Specification | 100mm · 5mm · bore 20mm |
| Use | Surface preparation / finishing selection; match profile, grit and backing to the workpiece. |
| Range-building advantage | A clearly specified diameter, bore and section lets buyers select by fit rather than appearance. |
Floor grinding block · 100mm
| Material | Diamond abrasive (catalog material) |
|---|---|
| Specification | 100mm · 8mm · bore 22mm |
| Use | Surface preparation / finishing selection; match profile, grit and backing to the workpiece. |
| Range-building advantage | A clearly specified diameter, bore and section lets buyers select by fit rather than appearance. |
Floor water-grinding disc · 80mm
| Material | Diamond abrasive (catalog material) |
|---|---|
| Specification | 80mm · Mesh size 60#, 120#, 200# |
| Use | Progressive surface finishing; select grit and a process compatible with the disc’s wet/dry rating. |
| Range-building advantage | Grit and backing choices let the assortment follow the required surface finish. |
Floor finishing disc · 100mm
| Material | Diamond abrasive (catalog material) |
|---|---|
| Specification | 100mm · Adhesive fabric, non-adhesive fabric · Mesh size30#、50#、80#、120# |
| Use | Surface preparation / finishing selection; match profile, grit and backing to the workpiece. |
| Range-building advantage | Grit and backing choices let the assortment follow the required surface finish. |
Sintered polishing disc · 100、80mm
| Material | Diamond abrasive (catalog material) |
|---|---|
| Specification | 100、80mm · Mesh size60#、120#、200# |
| Use | Progressive surface finishing; select grit and a process compatible with the disc’s wet/dry rating. |
| Range-building advantage | Grit and backing choices let the assortment follow the required surface finish. |
Abrasive cutting disc · 100mm
| Material | Request the abrasive grade for your application |
|---|---|
| Specification | 100mm · 2.5mm · bore 16mm |
| Use | Cutting with a matched guard, bore and speed rating; do not use a cutting disc for side grinding. |
| Range-building advantage | Grit and backing choices let the assortment follow the required surface finish. |
Buy the specification behind the accessory.
Does S2 or S3 alone prove a longer service life?
No. Steel grade is one part of the specification. Geometry, heat treatment, hardness, fit and the actual working conditions also matter. GEAKITA does not claim a service-life multiplier without a corresponding test.
Are all bits, sockets and extensions impact-rated?
No blanket impact rating is implied. Specify the exact tool and operating mode, then select rated components. Flexible extensions and ordinary sockets must not be assumed suitable for impact use.
Can every disc fit a GEAKITA angle grinder?
No. Match diameter, bore, maximum operating speed, guard and intended operation. A 22.23 mm bore does not automatically fit a 16 mm or 20 mm interface. Wet-use accessories also require a suitable machine and working method.
Can mixed sets use an upgraded steel grade?
Specify the material for each component in your OEM brief. Mixed sets may contain different grades; an S2 designation should identify the applicable components.